Last Update: Jun 7, 2024

Coding with AI

I wrote a book! Check out A Quick Guide to Coding with AI.
Become a super programmer!
Learn how to use Generative AI coding tools as a force multiplier for your career.


Do you want to safely overclock your Raspberry Pi? Here’s how you need to do it. There are a few articles out there on overclocking your Raspberry Pi, and I followed them but it didn’t work. So after some Googling and Stack Overflow work I find the answer, and I’m here to save you some time.

Find your current clock speed

There are several ways to find out what you Pi is running at currently. Most likely it’s running at 700mhz, and this is how you verify it

cat /proc/cpuinfo

After running this you should see the following output:

Processor : ARMv6-compatible processor rev 7 (v6l)

BogoMIPS : 697.95

Features : swp half thumb fastmult vfp edsp java tls

CPU implementer : 0x41

CPU architecture: 7

CPU variant : 0x0

CPU part : 0xb76

CPU revision : 7

Hardware : BCM2708

Revision : 000f

Serial : 0000000035dfc68c

Note the “BogoMIPS” is at 697.95. You can also run this:

cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq

Which displays your frequency in Hz, which should be 700000.

The best way to see what your Pi is really running is by using the following:

vcgencmd get_config arm_freq

It should say something like

arm_freq=700

*Note: it may say arm_freq=0 I have seen this happen too. Don’t fret about it.

This is the base frequency of 700 MHz, which is the default. But we want it to go faster than that right?

How to Overclock the Raspberry Pi

You can use software to overclock your Raspberry Pi and still be covered by the warranty. I gave some innaccurate information about this and was corrected in the comments:

Please note though that dynamic overvolting as you describe here doesn’t void your warranty; it’s only if you set “force_turbo=1” that we set the “warranty void” bit. - Eben Upton

The first thing you’ll want to do is modify your config.txt:

sudo nano /boot/config.txt

The config.txt is read by the GPU before the ARM core is initialized. It can be used to set various system configuration parameters such as overclocking.

In this file, you’ll want to add the following two lines:

arm_freq=800 sdram_freq=500

Note: These are the settings I found that get the most speed and stability. Your mileage may vary, feel free to play around with it. There are folks running at 1ghz just fine, but my unit didn’t function well at this level.

Now according to most instructions you can change this and just reboot. But it won’t always work. It didn’t for me. I found some advice on Stack Overflow and had to do the following:

sudo sync
sudo sh -c "echo 3 > /proc/sys/vm/drop_caches"
sudo cp config.txt config.txt.save
sudo cp config.txt config.txt.save.1
sudo sync; sync; exit; exit

This will log you out of your terminal, or terminal window, so log back in and type:

sudo sync; sync;
sudo shutdown -h now

Now, your Raspberry Pi will be shut down. Unplug it, and plug it back in.

Check your changes

To see what frequency you’re running at, issue the following command:

vcgencmd get_config arm_freq

It should say:

arm_freq=800

Congratulations, you’ve overclocked your Pi. For building large packages or just surfing the desktop you’ll notice a big difference.

If that doesn’t work

You can also overclock using the raspi-config utility. To get this, you’ll have to update your firmware, issue the following command:

sudo apt-get update && sudo apt-get install raspberrypi* raspi-config

Now with the updated firmware, start the raspi-config utility:

sudo raspi-config

You will see the following menu:

How to overclock a Raspberry Pi

And you’ll be shown the following options:

How to overclock a Raspberry Pi

I set mine to “Modest” at 800/250. As it says this is a modest overclocking and seems the safest.

After selecting your option, it will ask to reboot, say yes.

Again to check it, you can type in

vcgencmd get_config arm_freq

and it should say:

arm_freq=800

You can also check more options by typing:

vcgencmd get_config int

And it should look like this:

arm_freq=800

core_freq=250

sdram_freq=500

disable_overscan=1

boot_delay=1

temp_limit=85

Enjoy! As I said there are many different options and your results may vary. There are people running very fast speeds and not having stability or heat problems, I don’t know enough about the Pi to know exactly why that is. It could be a combination of environment and the tasks being performed.

Even more options

So do you want to play around with it some more? Of course, if you have the Raspberry Pi you’re likely a hacker anyway. Here is another update you can do to make the memory dynamic between the GPU and CPU.

sudo rpi-update 5fcbae1010c1ba99a77bab5198508bb9e6964d03

And add the following to your cmdline.txt

coherent_pool=2M cma=2M smsc95xx.turbo_mode=N

And add the following to config.txt

gpu_mem_256=160

gpu_mem_512=316

cma_lwm=16

cma_hwm=32

Reboot your Raspberry Pi. Now, you’ll always have a set number allocated to the ARM, it will have 96M of memory and the GPU will always have at least 20M. But, when the GPU gets low, it will request some memory from ARM, and vice versa. The cma_lwm is the “low water mark” meaning if it has less that memory available it will request it from ARM. If the GPU has more than cma_hwm (high water mark) it will release memory to the ARM.

How to overclock a Raspberry Pi

Summary

I hope this has helped you wade through some of the problems with overclocking the Raspberry Pi. It’s not always as straightforward as some of the tutorials suggest, but it isn’t terribly difficult. Here are some additional Raspberry Pi overlocking options if you want to play around even more.

For the most part you’ll probably want to run some pretty modest settings, but if you’re building something from source or doing a lot of video you’ll want to squeeze every bit of performance you can out of it.

Let me know what kind of configs you come up with and what works best for you!

Questions, comments? Let me know!


Want to learn more about the Raspberry Pi? Check out the Raspberry Pi for Developers course!



Stay up to date on the latest in Computer Vision and AI.

Get notified when I post new articles!

Intuit Mailchimp




Published: Dec 17, 2012 by Jeremy Morgan. Contact me before republishing this content.